The UK’s largest stockist of wudu products · Quotes in 30 minutes · Next-day UK delivery0333 577 0513Book a free consultation
Guides · Installing a wudu station

Installing a wudu station: plumbing, drainage and what to check.

What a plumber needs to install a WuduWash unit: fixings, waste sizes, tap pressures, weights, recessed troughs and a checklist for the day.

By the WuduWash technical team · Updated 20 November 2026 · 7 minute read

This guide is for the person holding the tools. It gathers the fixing, waste and water details from our specification sheets in one place. Always work from the specification sheet for the exact unit, which is on its product page and on the Specifiers page.

The short versionEvery unit arrives with pipework, wastage and taps. Check four things before the day: how the unit fixes, where the waste leaves, what water pressure the tap needs, and whether the floor and the route in can take the weight.

1. How each type fixes

UnitFixingWeight
Dual Level Wall MountedWall-hung or floor-mounted. Hangers supplied.47 kg gross
Dual Level Floor Mounted and Dual Level 2.0Floor mounted.50 kg
Foot wash troughsFloor-mounted or recessed. Between walls or freestanding.See specification sheet
All-in-one and front trough unitsRear wall fixing with keyhole slots. Stools bolt to the floor with fixing tabs.See specification sheet
Anti-ligature unitsFloor mounted, with a bolt-on stool option.See specification sheet
Wheelchair UnitWall keyhole slots and floor fixing holes.See specification sheet
FlowFreestanding solid surface, assembled from base, side and back panels.120 kg gross
PodFreestanding solid surface.214 kg net, 300 kg gross
HayatMarble sink and stool in a solid surface frame.435 kg net, 589 kg gross

For the Flow, Pod and Hayat, check the floor loading and measure the doors, lifts and corridors on the way in.

2. Waste and drainage

  • Dual Level 2.0 and Paradise: water inlet and waste through the floor, with an S-trap.
  • All-in-one and front trough units: 45 mm waste outlet, 1½ inch BSP. The all-in-one has a removable front panel for pipework access.
  • Anti-ligature units: 45 mm waste outlet, with an access panel for maintenance.
  • Foot wash troughs: the waste can be on the left or the right, through a 101 mm outside-diameter tube dropper.
  • Recessed troughs: the recess cut-out is 440 mm wide and 90 mm deep, by the length of the trough.

Units drain through their own waste. In a busy room a floor gully is still worth having, because some water always reaches the floor. See wudu area design.

3. Taps and water pressure

TapSupplyPressure
Timed Flow Bib TapSingle hot or cold supply, ½ inch BSP inlet. Runs about 12 seconds per press.0.2 to 5 bar working, 10 bar maximum static
Sensor TapCold or premixed supply. Mains or battery powered.0.5 to 9 bar
Pull-Out Mixer TapHot and cold, ½ inch BSP with flexible connectors. Fits the Paradise and Flex.1 to 3 bar. High-pressure systems only, not gravity-fed

For warm water from a single-supply tap, the water must be blended before it reaches the tap. Fit the thermostatic mixing and backflow protection that the water fittings regulations and the building's own policy require. That is the installer's responsibility.

4. Before the day

  1. Download the specification sheet for the exact unit and finish.
  2. Confirm the wall or floor can take the fixing and the weight.
  3. Mark the supply and waste positions, and whether they come through the wall or the floor.
  4. Check the water pressure against the tap.
  5. Check the route in for size and weight.
  6. Agree the floor finish and any falls with the designer before the unit goes down.

5. After fitting

  • Run every tap and check each waste for leaks before any panel goes back on.
  • Set the flow on timed taps. The Timed Flow Bib Tap has five settings and leaves the factory at the middle one.
  • Fit signage so the unit is not mistaken for an ordinary sink.
  • Show the cleaning team the unit, including any hinged grate on a trough.

If you would rather not fit it yourself, our own team installs from £99, and our support line is open by phone, email and WhatsApp. Call 0333 577 0513.

Questions

Can any plumber install a wudu station?

Most plumbers can. Every WuduWash product arrives with pipework, wastage and taps, and each has a specification sheet. Our own team can also install, from £99.

What waste size does a wudu unit need?

The stainless steel all-in-one, front trough and anti-ligature units have a 45 mm waste outlet. Foot wash troughs drain through a 101 mm outside-diameter tube dropper. Check the specification sheet for the exact unit.

Can a foot wash trough be recessed into the floor?

Yes. WuduWash foot wash troughs can be floor-mounted or recessed. The recess cut-out is 440 mm wide and 90 mm deep, by the length of the trough.

What water pressure do wudu taps need?

The Timed Flow Bib Tap works from 0.2 to 5 bar and the Sensor Tap from 0.5 to 9 bar. The Pull-Out Mixer Tap needs 1 to 3 bar and is not suitable for gravity-fed systems.

Planning a wudu area?

Send us your drawings and we will reply with a layout and a quote. We aim to answer within 30 minutes in working hours.

Open the 3D StudioBook a consultation